Running On Device #

It's always a good idea to test your app on an actual device before releasing it to your users. This document will guide you through the necessary steps to run your React Native app on a device.

Setting up an iOS device #

Installing an app on an iOS device requires a Mac, an Apple ID, and a USB cable.

Connect your device to your Mac via USB, then open Xcode. In the project navigator, choose your device from the Product > Destination toolbar menu. Xcode will then register your device for development.

If you run into any issues, please take a look at Apple's Launching Your App on a Device docs.

Finally, select your phone as the build target and press Build and run.

Setting up an Android device #

Running an Android app on a device requires a Mac or PC and a USB cable.

1. Enable Debugging over USB #

Most Android devices can only install and run apps downloaded from Google Play, by default. You will need to enable USB Debugging on your device in order to install your app during development.

To enable USB debugging on your device, you will first need to enable the "Developer options" menu by going to Settings → About phone and then tapping the Build number row at the bottom seven times. You can then go back to Settings → Developer options to enable "USB debugging".

2. Plug in your device via USB #

Let's now set up an Android device to run our React Native projects. Go ahead and plug in your device via USB to your development machine.

Next, check the manufacturer code by using lsusb (on mac, you must first install lsusb). lsusb should output something like this:

These lines represent the USB devices currently connected to your machine.

You want the line that represents your phone. If you're in doubt, try unplugging your phone and running the command again:

You'll see that after removing the phone, the line which has the phone model ("Motorola PCS" in this case) disappeared from the list. This is the line that we care about.

Bus 001 Device 003: ID 22b8:2e76 Motorola PCS

From the above line, you want to grab the first four digits from the device ID:

22b8:2e76

In this case, it's 22b8. That's the identifier for Motorola.

You'll need to input this into your udev rules in order to get up and running:

Make sure that you replace 22b8 with the identifier you get in the above command.

Now check that your device is properly connecting to ADB, the Android Debug Bridge, by running adb devices.

Seeing device in the right column means the device is connected. You must have only one device connected at a time.

3. Run your app #

Type the following in your command prompt to install and launch your app on the device:

If you get a "bridge configuration isn't available" error, see Using adb reverse.

Hint

You can also use the React Native CLI to generate and run a Release build (e.g. react-native run-android --configuration Release).

Connecting to the development server #

You can also iterate quickly on a device using the development server. You only have to be on the same Wi-Fi network as your computer. Shake the device to open the Developer menu.

You can also iterate quickly on a device by connecting to the development server running on your development machine. There are several ways of accomplishing this, depending on whether you have access to a USB cable or a Wi-Fi network.

Method 1: Using adb reverse (recommended) #

You can use this method if your device is running Android 5.0 (Lollipop), it has USB debugging enabled, and it is connected via USB to your development machine.

Run the following in a command prompt:

You can now use Reload JS from the React Native in-app Developer menu without any additional configuration.

Method 2: Connect via Wi-Fi #

You can also connect to the development server over Wi-Fi. You'll first need to install the app on your device using a USB cable, but once that has been done you can debug wirelessly by following these instructions. You'll need your development machine's current IP address before proceeding.

You can find the IP address in System Preferences → Network.

Open the command prompt and type ipconfig to find your machine's IP address (more info).

Open a terminal and type /sbin/ifconfig to find your machine's IP address.

1. Make sure your laptop and your phone are on the same Wi-Fi network.
2. Open your React Native app on your device.
3. You'll see a red screen with an error. This is OK. The following steps will fix that.
4. Open the in-app Developer menu.
5. Go to Dev Settings → Debug server host for device.
6. Type in your machine's IP address and the port of the local dev server (e.g. 10.0.1.1:8081).
7. Go back to the Developer menu and select Reload JS.

Building your app for production #

You have built a great app using React Native, and you are now itching to release it in the App Store. The process is the same as any other native iOS app, with some additional considerations to take into account.

Building an app for distribution in the App Store requires using the Release scheme in Xcode. To do this, go to Product → Scheme → Edit Scheme (cmd + <), make sure you're in the Run tab from the side, and set the Build Configuration dropdown to Release.

Apps built for Release will automatically disable the in-app Developer menu, which will prevent your users from inadvertently accessing the menu in production. It will also load the JavaScript locally, so you can put the app on a device and test whilst not connected to the computer.

Hint

You can also use the React Native CLI to perform this operation using the option --configuration with the value Release (e.g. react-native run-ios --configuration Release).

Once built for release, you'll be able to distribute the app to beta testers and submit the app to the App Store.

App Transport Security #

App Transport Security is a security feature, added in iOS 9, that rejects all HTTP requests that are not sent over HTTPS. This can result in HTTP traffic being blocked, including the developer React Native server.

ATS is disabled by default in projects generated using the React Native CLI in order to make development easier. You should re-enable ATS prior to building your app for production by removing the NSAllowsArbitraryLoads entry from your Info.plist file in the ios/ folder.

To learn more about how to configure ATS on your own Xcode projects, see this post on ATS.